04fxt
New member
Hi folks, as most of you know I love buying cut up gun parts from other countries and rebuilding them in semi-auto form for my own amusement.
I figured I would stop clogging the gun thread with lengthy posts about building guns, and just make my own thread.
I usually build AK's, but this time it's an Uzi. The parts are from a 1965 IMI(Israeli Military Industries) 9mm sub machine gun. Those not familiar with this process, here's what happens. The foreign made machine gun or sub machine gun in this case, is torch cut in 3 places across the receiver to render the gun useless. Then it is imported to the USA, and sold as a "parts kit" to someone like myself. The parts kit is not considered a firearm as the receiver is the part designated by the ATF to be the actual "gun", therefore they consider the parts to be scrap metal until it is rebuilt into a functioning semi-auto firearm.
This will be built as a semi-auto carbine. Meaning it will have a 16" barrel(minimum length without $$ and lots of paperwork) and it will have a folding stock. The overall length with the stock extended needs to be no less than 26"(again with the laws...).
Since the firearm is made from foreign parts, you can use them, but you have to comply with 922r federal regulations. In short, it states that a foreign made firearm has to contain less the 10 imported parts once it is finished. There are quite a few differences in firearms, so there are lists from the ATF of which parts are counted and which are not. Then you need only make sure when the new gun is assembled, that you have the proper number of 922r compliant parts, and thus you will have a legally built compliant rifle.
Most imported parts kits can be reassembled with new parts for 922r and a lot of companies make 922r USA made compliant parts for this very reason. It can be tricky, so you need to read up on the ATF's site to make sure you are doing it right.
The biggest part is getting the proper parts to convert to semi-auto. Luckily there are quite a few places to get semi Uzi parts for rebuilding on an old parts kit. Most folks would buy a new receiver made for semi only and assemble it from there. I want to keep the old serial # and coat of arms stamped on the old cut receiver pieces, so I am going to buy a semi receiver and cut the ends off to match to my cut pieces from my parts kit, then tig weld it back together in a jig.
It will be a long process, but it is much more satisfying and also has a certain "cool" factor since the original markings will remain on the receiver. A few things need to be done to the receiver in the build process to ensure that it can only be used as a semi-auto, one of which is welding in a small block to the right rear section to prevent dropping in a full-auto bolt assembly. The other is to weld in a semi-auto feed ramp, that has a loop over the top of the barrel to prevent the full-auto bolt from closing on it.
Most of the parts to be used I will buy, leaving the biggest part to be the rewelding process. Should be fun, and I will make sure to post pics when I make progress.
Sorry if I was a bit too detailed for those of you who already know the 922r stuff...
Anyway, here's the parts kit as I received it-
And the cool Hebrew selector markings on the grip frame

I figured I would stop clogging the gun thread with lengthy posts about building guns, and just make my own thread.
I usually build AK's, but this time it's an Uzi. The parts are from a 1965 IMI(Israeli Military Industries) 9mm sub machine gun. Those not familiar with this process, here's what happens. The foreign made machine gun or sub machine gun in this case, is torch cut in 3 places across the receiver to render the gun useless. Then it is imported to the USA, and sold as a "parts kit" to someone like myself. The parts kit is not considered a firearm as the receiver is the part designated by the ATF to be the actual "gun", therefore they consider the parts to be scrap metal until it is rebuilt into a functioning semi-auto firearm.
This will be built as a semi-auto carbine. Meaning it will have a 16" barrel(minimum length without $$ and lots of paperwork) and it will have a folding stock. The overall length with the stock extended needs to be no less than 26"(again with the laws...).
Since the firearm is made from foreign parts, you can use them, but you have to comply with 922r federal regulations. In short, it states that a foreign made firearm has to contain less the 10 imported parts once it is finished. There are quite a few differences in firearms, so there are lists from the ATF of which parts are counted and which are not. Then you need only make sure when the new gun is assembled, that you have the proper number of 922r compliant parts, and thus you will have a legally built compliant rifle.
Most imported parts kits can be reassembled with new parts for 922r and a lot of companies make 922r USA made compliant parts for this very reason. It can be tricky, so you need to read up on the ATF's site to make sure you are doing it right.
The biggest part is getting the proper parts to convert to semi-auto. Luckily there are quite a few places to get semi Uzi parts for rebuilding on an old parts kit. Most folks would buy a new receiver made for semi only and assemble it from there. I want to keep the old serial # and coat of arms stamped on the old cut receiver pieces, so I am going to buy a semi receiver and cut the ends off to match to my cut pieces from my parts kit, then tig weld it back together in a jig.
It will be a long process, but it is much more satisfying and also has a certain "cool" factor since the original markings will remain on the receiver. A few things need to be done to the receiver in the build process to ensure that it can only be used as a semi-auto, one of which is welding in a small block to the right rear section to prevent dropping in a full-auto bolt assembly. The other is to weld in a semi-auto feed ramp, that has a loop over the top of the barrel to prevent the full-auto bolt from closing on it.
Most of the parts to be used I will buy, leaving the biggest part to be the rewelding process. Should be fun, and I will make sure to post pics when I make progress.
Sorry if I was a bit too detailed for those of you who already know the 922r stuff...
Anyway, here's the parts kit as I received it-

And the cool Hebrew selector markings on the grip frame
