Search results

cool thanks, hopefully it does not cause me any issues in the future, all fluids are sparkly clean, and good gas mileage so far from what i can tell. i was just curious if someone has a parts motor laying around i could snag a sensor from.

Do I necessarily need to go with new? I was quoted almost $70 to replace, half the time I swap sensors out with known good ones from other motors. Can it just be cleaned?

just found a 99 outback 2.5 mt, $200 and all it needed was a battery to drive it home 90 miles. got a check engine code on the way back of P0325 rear knock sensor. is it the same as the front one? it flickers on and off occasionally but the car runs awesome either way. the past owner said its...

I put it on with an impact wrench with plenty of pressure, I think what happened was the balljoint spun with the nut and did not actually torque down properly. I used a tire iron on wheel nut and I had to hold it with a pair of vice grips. its still holding so I guess we will see when I start...

I just replaced the entire knuckle, brakes, strut etc... With the ones from my parts car in far better condition. This car has 250k, I think this is going to be the last balljoint I'm going to be replacing on this car. I wagon, I am in sopo but I can go anywhere in the greater Portland area, I...

Now I'm paranoid so I want to weld this lugnut straight to the control arm. If that had fallen off on the highway there would be no more subie.

Always remember to double check your nuts and bolts you do it your selfers! I just had the nut holding on my balljoint to the lower control arm let go (castle nut nowhere to be found) and the cotter pin missing??? Anyways, just a friendly reminder so no one else gets caught with uber camber in...

anyone want the old transmission for a rally rig or parts? 4.11 FD goes into all gears fine except for 5th synchro's are a bit worn. I wanted the other transmission because it has less miles and has higher ratios in 3-5 for better highway mileage. make any offer, ill probably take it.

Redneck style yeah.... 

Thanks, my goal is to have the replacement ready to go back in tonight, and driving it tomorrow!

I pulled the intake off and looked down inside, its indeed cracked. I compared it to a good fork I just picked up. the clutch slave cylinder moves freely and fully now, it just had really dirty fluid in it. I now have it jacked up 2' and pulled the exhaust off. what is the best point to support...

I pulled the intake off and looked down inside, its indeed cracked. I compared it to a good fork I just picked up. the clutch slave cylinder moves freely and fully now, it just had really dirty fluid in it. I now have it jacked up 2' and pulled the exhaust off. what is the best point to support...

I did my clutch about 8k ago almost exactly one year ago when I first bought it so nothing by the engine will be difficult, I'm more concerned about how to separate the rear drive shaft and what's the best technique getting it lined back up again. Cherry pickers can be adjusted, but floorjacks...

so i have no idea how i managed to do this, but i managed to CRACK and bend the shift fork connected to the throw out bearing and slave cylinder. does anyone happen to have one already removed from a 5 speed outback/legacy GT or have one easily accessible from a car with a motor pulled?? this is...

My father just bought a 2005 Chevy Colorado I5 3.5l truck and wants to know if there are any vendors who do performance tuning could flash the Ecu for better fuel economy rather than performance. Anyone who knows chevys and could let me know about some reliable shops that work on them locally...

I was worried I broke something when I curbed my Subaru. Nope, all in one piece because Subaru.

Congrats!

Who got the video of me drifting the turdback?

took mine out. brakes are sticking, oil gasket leak, shifter is finicky. and front fork seals are leaking... fired right up and idles perfectly though!

i have a trans. out of a 1998 outback, had it doing 80 on the highway before i decided to start parting it out. stil in the vehicle, i was going to start pulling the driveline out this week. $200 if i pull it.